2. MODELING

CHAPTER 2 "MODELLING" 126 "RESULTS OF GENERAL AUDITS" error1001 Beam %-d (%-d) does not have a mathematical delegate\n Error1002 Pillar %-d (%-d) has no mathematical representative\n Error1003 Member %-d of Beam %d has a problem with the start-end nodes (zero) (%-d-%-d)\n Error1003 Member %-d of Beam %d (%-d) has identical start-end nodes (%-d)\n Error1003 Member %-d of Column %d has a problem with start-end nodes (zeroes) (%-d-%-d)\n Error1004 Member %-d of Pillar %d (%-d) has identical start-end nodes (%-d)\n Error1003 Member %-d of beam %d has short length = %-.2f \n Error1003 Member %-d of the beam %d (%-d) has a short length = %-.2f \n Error1004 Member %-d of Pillar %d has a short length = %-.2f\n Error1004 Member %-d of Pillar %d (%-d) has a short length= %-.2f\n Error1005 There are Members with the same name (%-d)\n Error1006 Member (%-d) (%-d) is the same as Member (%-d) (%-d) (%-d) (Syndication)\n Error1005 There are Members with the same name (%-d) \n Error1006 Member (%-d)(%-d)(%-d) is the same as Member (%-d)(%-d)(%-d) (Linkage)\n Error1005 There are Members with the same name (%-d) \n Error1006 Member (%-d)(%-d)(%-d) is the same as Member (%-d)(%-d)(%-d) (Linkage)\n Error1005 There are Members with the same name (%-d) \n Error1006 Members (%-d)(%-d)(%-d) and (%-d)(%-d)(%-d) have the same start node and the same end node. Error1007 There are nodes with the same name (%-d)(%-d) \n Error1007 Node %-d has the same coordinates as node %-d(%-d) [%-.3f cm]\n Error1008 Node (%-d)(%-d)(%-d) does not have a correct aperture node \n Error1009 The start node of the beam %d is wrong\n Error1009 The end node of Beam %d is wrong\n Error1010 The start node of Pillar %d is wrong\n Error1011 The end node of Pillar %d is wrong\n Error1012 Node %d of surface 3D %d is wrong\n Error1013 The start node %-d of the Fieldbus %d (%-d) has the wrong degrees of freedom\n Error1014 The end node %-d of the Pedigree node %d (%-d) has the wrong degrees of freedom\n Error1015 The Member %-d of Beam %d (%-d) has an error %- s\n Error1016 Member %-d of Pillar %d (%-d) is wrong %-s\n Error1017 Beam %-d (%-d) at its end is not connected\n Error1017 Beam %-d (%-d) at its end is not connected Physically NO Mathematically YES\n Error1018 Beam %-d (%-d) has no connection to other members in the vector\n Error1019 Column %-d (%-d) has no connection to other members in the vector\n Error1020 In Field %-d, the Node of\n is not correct error1021 In Field %-d the correspondence of the poles is not correct\n error1022 The connection to Pillar %d (Node=%d)\n Error1301 Member %-d of Beam %d is placed vertically (%-d-%-d)\n Error1049 On the surface %-d (level 0) there are surface members which are not defined as grids on elastic ground (paving) error1301 The Member %-d of Pillar %d has been placed vertically (%-d-%-d)\n